ANSYS画弯矩图、剪力图、轴力图
梁单元的输出格式
根据 [官方文档][2]：输出数据格式：
Table 188.2: BEAM188 Item and Sequence Numbers
| Output Quantity Name | ETABLE and ESOL Command Input | |||
|---|---|---|---|---|
| Item | E | I | J | |
| Fx | SMISC | – | 1 | 14 |
| My | SMISC | – | 2 | 15 |
| Mz | SMISC | – | 3 | 16 |
| TQ | SMISC | – | 4 | 17 |
| SFz | SMISC | – | 5 | 18 |
| SFy | SMISC | – | 6 | 19 |
| Ex | SMISC | – | 7 | 20 |
| Ky | SMISC | – | 8 | 21 |
| Kz | SMISC | – | 9 | 22 |
| TE | SMISC | – | 10 | 23 |
| SEz | SMISC | – | 11 | 24 |
| SEy | SMISC | – | 12 | 25 |
| Area | SMISC | – | 13 | 26 |
| BM | SMISC | – | 27 | 29 |
| BK | SMISC | – | 28 | 30 |
| SDIR | SMISC | – | 31 | 36 |
| SByT | SMISC | – | 32 | 37 |
| SByB | SMISC | – | 33 | 38 |
| SBzT | SMISC | – | 34 | 39 |
| SBzB | SMISC | – | 35 | 40 |
| EPELDIR | SMISC | – | 41 | 46 |
| EPELByT | SMISC | – | 42 | 47 |
| EPELByB | SMISC | – | 43 | 48 |
| EPELBzT | SMISC | – | 44 | 49 |
| EPELBzB | SMISC | – | 45 | 50 |
| TEMP | SMISC | – | 51-53 | 54-56 |
| EXT PRESS [9] | SMISC | – | 62 | 66 |
| EFFECTIVE TENS [9] | SMISC | – | 63 | 67 |
| S:xx, xy, xz | LS | – | CI[1], DI[2] | CJ[1], DJ[2] |
| EPEL:xx, xy, xz | LEPEL | – | CI[1], DI[2] | CJ[1], DJ[2] |
| EPTH:xx | LEPTH | – | AI[3], BI[4] | AJ[3], BJ[4] |
| EPPL:xx, xy, xz | LEPPL | – | CI[1], DI[2] | CJ[1], DJ[2] |
| EPCR:xx, xy, xz | LEPCR | – | CI[1], DI[2] | CJ[1], DJ[2] |
| EPTO:xx, xy, xz | LEPTO | – | CI[1], DI[2] | CJ[1], DJ[2] |
| EPTT:xx, xy, xz | LEPTT | – | CI[1], DI[2] | CJ[1], DJ[2] |
| NL: SEPL, SRAT, HPRES, EPEQ, CREQ, PLWK | NLIN | – | EI[5], FI[6] | EJ[5], FJ[6] |
| *The following output quantities are valid for ocean loading only and are averaged values for the element: [10]* | ||||
| GLOBAL COORD | NMISC | 1, 2, 3 | – | – |
| VR, VZ | NMISC | 4, 5 | – | – |
| AR, AZ | NMISC | 6, 7 [7] | – | – |
| PHDYN | NMISC | 8 [7] | – | – |
| ETA | NMISC | 9 [7] | – | – |
| TFLUID | NMISC | 10 | – | – |
| VISC | NMISC | 11 | – | – |
| REN, RET | NMISC | 12, 13 [8] | – | – |
| CT | NMISC | 14 | – | – |
| CDY, CDZ | NMISC | 15, 16 | – | – |
| CMY, CMZ | NMISC | 17, 18 [7] | – | – |
| URT, URN | NMISC | 19, 20, 21 | – | – |
| ABURN | NMISC | 22 [7] | – | – |
| AN | NMISC | 23, 24 [7] | – | – |
| FX, FY, FZ | NMISC | 25, 26, 27 | – | – |
| ARGU | NMISC | 28 [7] | – | – |
具体参数可在ANSYS的Help中找到，一个较好的方法，在HELP中搜索SMISC即可对应找到各单元类型的设置方法了。
设定Element Table
General PostProc-> Elemnet table -> Define Table
定义Lable, 然后从下面的选项框中选择By Sequence num ，右边选择SMISC，在下方输入对应的编号。
Plot Element Table
在General PostProc->Plot Result -> Contor Plot -> Line Element Res中选择对应的I和J
就可以画出对应的剪力图，弯矩图，轴力图
参考链接：
[1]:http://blog.sina.com.cn/s/blog_5e94ccea0100zj4f.html
[2]:http://blog.sina.com.cn/s/blog_5e94ccea0100zj4f.html