stm32 SPI + DMA

Question

我尝试使用 DMA 通道通过 SPI 发送数据。当我在没有 DMA 的情况下发送时，一切都很好，但是使用 DMA 是错误的。当我调试我的程序时，SPI DR 寄存器始终为 0。我想一直使用 dma 循环模式来发送我的数组。有我的代码 GPIO 初始化：

GPIO_InitTypeDef GPIO_InitStructure;
RCC_APB2PeriphClockCmd(SPI_PERIPH_CLOCK, ENABLE);
RCC_AHBPeriphClockCmd(GPIO_PERIPH_CLOCK, ENABLE);
RCC_AHBPeriphClockCmd(RCC_AHBPeriph_DMA1, ENABLE);

GPIO_PinAFConfig(GPIOB, AF_PIN_SOURCE, GPIO_AF);

GPIO_InitStructure.GPIO_Pin = GPIO_PIN_5;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF;
GPIO_InitStructure.GPIO_OType = GPIO_OType_PP;
GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_DOWN;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;

GPIO_Init(GPIOB, &GPIO_InitStructure);

SPI 初始化

SPI_I2S_DeInit(SPI1);

SPI_InitTypeDef SPI_InitStructure;
SPI_InitStructure.SPI_Mode = SPI_Mode_Master;
SPI_InitStructure.SPI_Direction = SPI_Direction_1Line_Tx;
SPI_InitStructure.SPI_DataSize = SPI_DataSize_16b;
SPI_InitStructure.SPI_CPOL = SPI_CPOL_Low;
SPI_InitStructure.SPI_CPHA = SPI_CPHA_1Edge;
SPI_InitStructure.SPI_NSS = SPI_NSS_Soft;
SPI_InitStructure.SPI_BaudRatePrescaler = SPI_BaudRatePrescaler_32;
SPI_InitStructure.SPI_FirstBit = SPI_FirstBit_MSB;
SPI_InitStructure.SPI_CRCPolynomial = 7;
SPI_Init(SPI1, &SPI_InitStructure);

SPI_Cmd(SPI1, ENABLE);

DMA 初始化：

    DMA_InitTypeDef dma;
    DMA_DeInit(DMA1_Channel1);
    DMA_StructInit(&dma);

    dma.DMA_PeripheralBaseAddr = (uint32_t)&SPI1->DR;
    dma.DMA_PeripheralInc = DMA_PeripheralInc_Disable;
    dma.DMA_PeripheralDataSize = DMA_PeripheralDataSize_HalfWord;
    dma.DMA_MemoryBaseAddr = (uint32_t)spi_tx_buffer;
    dma.DMA_MemoryInc = DMA_MemoryInc_Enable;
    dma.DMA_MemoryDataSize = DMA_MemoryDataSize_HalfWord;
    dma.DMA_DIR = DMA_DIR_PeripheralDST;
    dma.DMA_BufferSize = BUFFERSIZE;   
    dma.DMA_Mode = DMA_Mode_Circular;
    dma.DMA_M2M = DMA_M2M_Disable;

    DMA_ITConfig(DMA1_Channel1, DMA_IT_TC, ENABLE);

    NVIC_InitTypeDef NVIC_InitStructure;

    NVIC_InitStructure.NVIC_IRQChannel = DMA1_Channel1_IRQn;
    NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 6;
    NVIC_InitStructure.NVIC_IRQChannelSubPriority = 0;
    NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
    NVIC_Init(&NVIC_InitStructure);

    DMA_Init(DMA1_Channel1, &dma);
    SPI_I2S_DMACmd(SPI1, SPI_I2S_DMAReq_Tx, ENABLE);

    DMA_Cmd(DMA1_Channel1, ENABLE);

简单的主要

int main(void) {

periph_init();

while (1) {     
    for(int j=0; j<10000000; j++){
        j++;
        j--;
    }
}
return 0;
}

我做错了什么？

Answer 1

正如我在 cmets 中提到的，您的 SPI 与 DMA1_Channel1 没有任何联系。根据this data sheet，你应该使用DMA1_Channel3。